Bike Line Dealer Locator
 
 
 
 
VisaMasterCardAmerican ExpressDiscoverPayPal
 

Be Safe! Use Quick Releases Correctly!

Please note that this video shows the quick release being unscrewed and removed from the wheel so that you can see all the parts. But, when using your quick releases you only need to unscrew or screw them in for adjusting the tightness, and you would never need to remove them completely except for hub repairs. Please read this entire page for full instructions on quick release use.

Incorrect quick-release use is dangerous because these mechanisms hold the wheels in place. The most common mistake is simply turning the lever like a nut until the wheel seems tight. Used this way the lever and wheel can loosen as you ride leading to catastrophe.

Watch this video and read the instructions below to learn how to properly use a quick release.

Please contact us if you're still unsure how to use this crucial piece of equipment after reading this tutorial.

Get to know your quick release. Click here for a close-up of the quick release showing all the parts.

Inspecting Your Quick Release

There are two ways to tell if the lever is open: most levers are marked "open" and "closed" so look for these markings. Also, levers are usually curved. When the bend protrudes outward like a bump, the lever is closed. When the bend is cupped, the lever is open. Closing and opening the lever requires flipping it 180 degrees, not spinning it.

Read the qick release lever to tell if it's safe. If it reads "open," the wheel can come off!!Read the lever to tell if it's safe. If it reads "open," the wheel can come off!!

Even if the lever reads "closed" and looks right, it's a good idea to test how tight it is by trying to open it by pulling on it. If it resists, it's tight and safe. If it opens with only a little effort, it's not tight enough. Follow our directions to tighten it.

Adjusting And Closing Your Quick Release

Animated Quick ReleaseWith the wheel centered in the fork (or frame), adjust the quick release by opening it, holding both ends and turning one clockwise until, when you close the lever, you feel some resistance. At this point, try to close the lever. The adjustment is correct when you can fully close the lever but with some effort (the lever should leave its impression in the palm of your hand). If you can only close the lever part way, open it, unscrew the adjustment slightly and try again.

Removing And Installing Your Wheel

Most forks have wheel-retention tabs on them, which are small protrusions that keep a loose wheel from falling out of the dropouts. The quick release must be open and adjusted by unscrewing to clear these tabs when you remove and install the wheel.

Quick Release - Removing and Installing Your Wheel

To do this, hold both ends of the quick release and turn one counterclockwise to unscrew it until there's enough clearance for the wheel to drop out of or fit into the fork (note that this adjustment is unnecessary on most rear wheels because retention tabs aren't used).

Quick Release Tips

  • The quick-release levers should be on the left side of the bike.
  • Quick releases must be fully closed to ensure safety.
  • If you close the lever in such a way that it aligns with the fork (see animation) and stays, you'll have something to grip while squeezing the lever. It'll also keep the lever tucked away where it can't snag anything, which might happen leaning your bike next to another in a bike rack, for example.
  • If you ever unscrew the quick release until it comes apart, don't panic! Just try not to lose the little springs. They're not crucial and the quick release will work without them. They're only there to provide spring pressure to maintain some clearance between the ends of the quick release and the axle locknuts to make it easier to slide the wheel into the frame. To reinstall the springs, make sure that the narrow ends point inward (see photo).

Basic Maintenance

  • Periodically Lube Your Quick ReleaseAbout once a month, lube your quick-release levers because dry levers won't work well and can feel tight when they're not.
  • Aluminum quick-release levers usually press against bushings as you close the lever. Lightly lube where the lever contacts the bushing (photo), to keep the quick release operating properly.
  • Steel levers usually pivot inside the cap. Apply lube to trickle inside the lever's pivot point.
  • If there's a nut or screw holding the lever (look beneath the cap), snug it with a wrench or screwdriver to make sure it's tight.
 

CONVENIENT BIKE LINE LOCATIONS  The Delaware Valley's Premier Bicycle Stores

QUICK LINKS

Allentown
1728 Tilghman Street
Allentown, PA 18104
610-437-6100

Bethlehem
2112 Schoenersville Road
Bethlehem, PA 18018
610-691-0943

Broomall
26 S. Sproul Rd.
Broomall, PA 19008
610-356-3022

Exton
292 East Lincoln Hwy.
Exton, PA 19341
610-594-9380

Lancaster
117 Rohrerstown Road
Lancaster, PA 17603
717-394-8998

Middletown
Marketplace Shopping Center
486-488 Middletown Warwick Road
Middletown, DE 19709
302-285-0134

Montgomeryville
803 Horsham Rd.
Montgomeryville, PA 18936
215-361-7900

Newark
212 East Main Street
Newark, DE 19711
302-368-8779

Pottstown
1386 N. State Street & Rt.100
Pottstown, PA 19464
610-718-5475

Valley Forge/Wayne
Gateway Shopping Center
111 East Swedesford Road
Wayne, PA 19087
610-688-5880

Warminster
375 York Road
Warminster, PA
215-675-1739

West Chester
Turner Square Shopping Center
117-119 Turner Ln
West Chester, PA 19380
610-436-8984

Wilmington
2900 North Concord Pike
Wilmington, DE 19803
302-479-9438

LOCATIONS
Bike Line Locations
Stowe Ski Shop Locations

PRODUCTS
Shop Online
Closeout Bikes
Bikes
Accessories
Gift Cards

INFORMATION
Employment Opportunities
Apply Online
Join Our Email
Frequently Asked Questions
Military Discount
Preferred Customer Club
Mountain Bike Team
Your Privacy
Policies and Shipping
Site Map
Home